안녕하세요 에듀이노 개발팀입니다.
이전에 잘못된 정보를 제공해드린점 대단히 죄송합니다.
기술문의 답변간 불편함을 제공해드린점 양해부탁드리겠습니다.
온습도 센서 연결시, PC와의 연결이 끊어지는 등 오류 현상이 발생하는 것은, 온습도 센서의 결선중 VCC. GND의 결선 방향이 반대로 바뀌어 발생하는 문제로 보입니다.
센서의 핀 배열은 제조사 별로 다르기 때문에 결선 표 등을 참고 결선의 유의해야 하는 점 참고부탁드리겠습니다.
전원부(VCC, GND)의 결선이 반대로 되면 다른 제품들도 손상이 갈 수 있는 점 참고해주시기 바랍니다.
첨부된 아래 오류 메시지는 보드가 PC와 정상적인 연결이 되지 않아 발생하는 오류메시지로 연결되는 센서로 인해 발생하는 문제입니다.
센서의 DATA, VCC, GND핀이 제대로 결선이 되어있는지 다시한번 확인해주시기 바랍니다.
감사합니다.
[ Original Message ]
전부 연결된상태에서 센서를 제거하면 아래 처럼 쉴드 보드에 LED 작동합니다.
센서 연결 하는순간 PC에서도 연결이 끊어지고요
-------------------------------------------------------------------------------
브레드보드에 사진처럼 연결시 전원 및 LED에 불이 들어오지 않다가
쉴드에서 브레드보드로 가는 전원단자를 제거하면 쉴드 보드에 있는 파워 led에 불이 들어와있고, AREF led에서는 깜빡이는게 보여집니다.
--------------------------------------------------------------------------------
교육키트1 이더넷편 업로딩 오류메세지 문의드립니다.
처음에 보드만 연결해서 Blink 예제 실행했을때는 LED 깜빡이는거 확인 했는데요,
쉴드랑 led등 연결하고 예제 코드 1 업로딩 하면 아래와 같이 오류메세지가 뜹니다.
아두이노가 처음이다보니 모르겠어서 어떤문제인지 문의드립니다.
아두이노:1.8.13 (Windows 10), 보드:"Arduino Uno"
스케치는 프로그램 저장 공간 444 바이트(1%)를 사용. 최대 32256 바이트.
전역 변수는 동적 메모리 9바이트(0%)를 사용, 2039바이트의 지역변수가 남음. 최대는 2048 바이트.
스케치를 업로드 하는 동안 에러가 발생하였습니다.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xfc
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xfc
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xfc
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xfc
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xfc
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xfc
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xfc
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xfc
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xfc
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xfc
이 리포트는 파일 -> 환경설정에 "컴파일중 자세한 출력보이기"를
활성화하여 더 많은 정보를
보이게 할 수 있습니다.